Banner Safe Speed Monitoring Modules Bedienungsanleitung PDF herunterladen

For over-speed, under-speed, and zero-speed detection

For complete technical information about this product, including dimensions, accessories, and specifications, see www.BannerEngineering.com and search

for

140782_web.

The user is responsible for satisfying all local, state, and national laws, rules, codes, and regulations

relating to the use of this product and its application. Banner Engineering Corp. has made every effort to

provide complete application, installation, operation, and maintenance instructions. Please direct any ques-

tions regarding the use or installation of this product to the factory applications department at the telephone

numbers or address shown found at http://www.bannerengineering.com.

The user is responsible for making sure that all machine operators, maintenance personnel, electricians,

and supervisors are thoroughly familiar with and understand all instructions regarding the installation, main-

tenance, and use of this product, and with the machinery it controls. The user and any personnel involved

with the installation and use of this product must be thoroughly familiar with all applicable standards, some

of which are listed within the specifications. Banner Engineering Corp. makes no claim regarding a specific

recommendation of any organization, the accuracy or effectiveness of any information provided, or the ap-

propriateness of the provided information for a specific application.

Models Detectable Speed Range *

SSM-FM-11A10 5 to 10,500 ipm

SSM-FM-11A20 10 to 20,000 ipm

* The unit "ipm" (impulses per minute) may be equal to actual machine rpm, or may be a multiple, depending on the number of sensing points used.

WARNING: Not a Stand-Alone Safeguarding Device

This Banner product is not a stand-alone point-of-operation guarding device, as defined by OSHA regulations. It is necessa-

ry to install point-of-operation guarding devices, such as safety light screens and/or hard guards, to protect personnel from hazardous

machinery. Failure to install point-of-operation guards on hazardous machinery can result in a dangerous condition which

could lead to serious injury or death.

Indicators

Standstill / Under-speed Monitoring

Applications

Over-speed Monitoring Applica-

tions

Figure 1. SSM-FM-11A... features and terminal locations

1. Power ON (green)

when

Power is applied Power is applied

2. Safety output channel

1 ON (green) when

Standstill signal detected on Input

Channel 1

No over-speed detected on Input

Channel 1

2. Safety output channel

2 ON (green ) when

Standstill signal detected on Input

Channel 2

No over-speed detected on Input

Channel 2

SSM-FM-11A... Safe Speed Monitoring Modules

P/N 140782 rev. C 8/22/2012

0 140782 4

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - Indicators

For over-speed, under-speed, and zero-speed detectionFor complete technical information about this product, including dimensions, accessories, and spe

Seite 2 - Electrical Installation

Operation and RequirementsThe Module is redundant and self-checking. It requires digital input signals from two independent input sensors (e.g., proxi

Seite 3 - SSM-FM-1

Reset and Startup Conditions. The Module works only in automatic reset mode. In order forthe Module to switch to RUN mode for normal operation, the Y1

Seite 4 - Configuration

WARNING: WARNING . . . Wiring of Arc Suppressors. If arc suppressors are used, they MUST be installed as shown acrossthe coils of the Machine Primary

Seite 5 - Adjusting Simultaneity

Range Settings DIP Switch Banks A and BModel SSM-…10 Model SSM-…20 1 25–40 ipm 10–80 ipm OFF OFF1,200–10,500 2,400–20,000 OFF ON300–2,700 600–5,300 ON

Seite 6

12. Slowly turn the fine-tuning potentiometer clockwise (1 or 2 degrees at a time), pausing to allow the Module its necessary response time to detect

Seite 7 - Checkout Procedure

Checkout ProcedureCAUTION: Disconnect Power Prior to CheckoutBefore performing the initial checkout procedure, make certain all power is disconnected

Seite 8 - EC Declaration of Conformity

Input Requirements for PNP Input SensorsPNP Input Sensors: 24V dc (terminals S1s and S2s)Input current min.: 3 mA Input current max.: 25 mAMin. pulse

Weitere Dokumente für Spezialmaschinen Banner Safe Speed Monitoring Modules

Um das Dokument anzuzeigen Banner Safe Speed Monitoring Modules Bedienungsanleitung

Banner Safe Speed Monitoring Modules Bedienungsanleitung (15 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Banner Safe Speed Monitoring Modules Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Spezialmaschinen Banner Safe Speed Monitoring Modules herunter. Banner Safe Speed Monitoring Modules User Manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Spezialmaschinen Banner Safe Speed Monitoring Modules

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Spezialmaschinen Banner Safe Speed Monitoring Modules