Banner U-Gage Ultrasonic Sensor Bedienungsanleitung PDF herunterladen (Seite 38)

LIGHT GAUGING

ULTRASONIC

QT50U

S18U

QS18U

T30U/T30UX

M25U

T18U

Q45U

Q45UR

MEASURING

ARRAYS

RADAR

More information online at bannerengineering.com 329

Photoelectrics

Sensors

Fiber Optic

Sensors

Special Purpose

Sensors

Measurement &

Inspection Sensors

Vision

Wireless

Lighting &

Indicators

Safety

Light Screens

Safety

Laser Scanners

Fiber Optic

Safety Systems

Safety Controllers &

Modules

Safety Two-Hand

Control Modules

Safety Interlock

Switches

Emergency Stop &

Stop Control

U-GAGE

M25U Speciﬁcations

Sensing Range Normal Speed: 500 mm

High Speed: 250 mm

140KHz

Supply Voltage and Current Emitter: 10 to 30V dc (10% max. ripple) at less than 85 mA

Receiver: 10 to 30V dc (10% max. ripple) at less than 38 mA (exclusive of load)

Supply Protection Circuitry Protected against reverse polarity and transient voltages

Receiver Output Conﬁguration Bipolar (1 NPN & 1 PNP) solid-state output;

Normally Closed (output is activated when an object blocks the sensing beam)

Output Rating 100 mA (each output) with short circuit protection; see Note 1

OFF-state leakage current: NPN: < 200 μA sinking PNP: < 10 μA sourcing

ON-state saturation voltage: NPN: < 1.6V @ 100 mA PNP: < 3.0V @ 100 mA

Output Protection Circuitry Protected against short circuit conditions

Output Response Time Normal Speed: 4.0 milliseconds

High Speed: 3.0 milliseconds

Repeatability 1 millisecond

Delay at Power-up < 250 milliseconds

Delay for Switching Between

Normal and High Speed

20 milliseconds

Indicators Green Power LED: indicates Power ON

Amber Output LED: indicates output activated

Construction Housing: 316 Stainless Steel

LED window: Polysulfone

Connections Emitter: 4-pin Euro-Style QD

Receiver: 5-pin Euro-Style QD

QD cordsets ordered separately. See page 329.

Environmental Rating Leakproof design, rated IEC IP67 (NEMA 6), IP69K

Operating Conditions Temperature: -20° to +70° C

Max. Relative Humidity: 95% at 50° C non-condensing

Vibration and

Mechanical Shock

All models meet Mil. Std. 202F requirements method 201A (vibration: 10 to 60 Hz max. amplitude 0.06", max. acceleration 10G).

Also meets IEC 947-5-2; 30G 11 ms duration.

Certiﬁcations

Notes 1. NPN < 200 μA for load impedance > 3 KΩ; for load current of 100 mA, leakage < 1% of load current

2. When mounting the M25U, care should be taken to acoustically isolate the emitter and receiver to eliminate sound energy coupling

between the sensor pair. This is best accomplished with elastomeric materials between the sensor and rigid mounting brackets.

Hookups Diagrams Emitter Models: MI21 (p. 763)

Receiver Models: MI17 (p. 762)

Brackets

M25U

SMBM25A SMBM25B

pg. 659 pg. 659

Washdown Euro QD

See page 6852

Length

Threaded 5-Pin

Straight

2 m MQDCWD-506

9 m MQDCWD-530

Cordsets

Euro QD (With Shield)

See page 687

Length

Threaded 5-Pin

Straight Right-Angle

2 m MQDEC2-506 MQDEC2-506RA

5 m MQDEC2-515 MQDEC2-515RA

9 m MQDEC2-530 MQDEC2-530RA

Additional cordset information available.

See page 679.

Additional bracket information available.

See page 620.

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 65 66

Kommentare zu diesen Handbüchern

Keine Kommentare

Banner U-Gage Ultrasonic Sensor Bedienungsanleitung Seite 38

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Messen, Testen & Steuern Banner U-Gage Ultrasonic Sensor